RAILROAD RELATED TERMS

A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z

 A

AAR
Association of American Railroads.
AB Valve
The operating device used on freight cars for charging, applying, and releasing the brakes. Also called a triple valve
ABD Valve
An improvement of the AB Valve that features a quick release.
ABDW Valve
An improvement of the ABD Valve. Modifies the Emergency Portion and provides for accelerated buildup of brake cylinder pressure during quick service applications.
Absolute Block
A length of track in which no train or engine is permitted to enter while it is occupied by another train or engine.
Absolute Permissive Block (APB)
A designated section of track or tracks within which the movement of trains will be governed by block signals, whose indications supersede the superiority of trains. The block signals may be controlled manually or automatically.
Absolute Signal
A block or interlocking signal designated by an "A" market or the absence of a number plate.
Add, to
Couple car(s) to a train
Adhesion Coefficient
The ratio of tangential and normal force that exist between the wheel and the rail during motion.
AEI Tag
An electronic transponder located on the side of rail cars that identifies them to trackside readers.
Air Brake System
All of the devices and parts included in making an air brake for controlling the speed and stopping a locomotive or train. It is made up of the operating devices, the pipes, fittings and foundation brake gear.
Air Test
The act of operating the brake valve to determine that the air brake system was operating correctly and could stop the train if necessary.
Alley
A clear track in a switching yard.
Angle Cock
An appliance used for the purpose of opening or closing brake pipe on ends of cars, rear ends of tenders, and front ends of switch engines so equipped. Provision is made for supporting hose at proper angle.
APE
All Purpose Employee -- an employee that is a promoted engineer that can also be forced to work as a conductor or trainman.
Application
Consists of all of the operations from the time the brake pipe reduction is started until the brake is released.
Approach Signal
A signal that governs the approach to another signal.
Armed
When a 2-way EOT is in communication with the HOT allowing it to dump the train from the rear.
Articulated [Mallet]
A Mallet locomotive. A simple articulated is a mallet which had a large enough boiler to supply all four cylinders with high pressure steam direct from the boiler. A compound mallet is a mallet which had a boiler too small to supply high pressure steam to all four cylinders at once, and used steam twice, once to the rear high pressure cylinders and the "partially used" steam would then supply the front cylinders. The best known example of a compound mallet is the N&W Y6b mallet, which "shifted" to compound operation at higher speed. Some well known simple articulated's are the UP BIG Boy, the UP Challenger, the N&W Class A, the B&O EM-1 type, and the SP AC class.
ARU
American Railway Union, Crushed during the Pullman strike in 1894
Automatic Block Signal System (ABS)
A series of consecutive blocks governed by block signals, cab signals or both, actuated by a train, engine or by certain conditions affecting the use of a block.
Automatic Cab Signal System (ACS)
A system which provides for the automatic operation of the cab signals and cab warning whistle.
Automatic Stop Arm
Mechanical arm located on the wayside, in conjunction with a wayside signal, which causes an emergency brake application when a train passes the signal at danger and the arm is in tripping position.
Automatic Train Stop System (ATS)
A system actuated by wayside inductors, so arranged that its operation will automatically result in the application of the brakes until the train has been brought to a stop.
Auxiliary Reservoir
A reservoir located on each rail car that stores air supplied by the locomotive.

B

Baby Lifter
A brakeman.
Bad Order
A piece of rolling stock that needs repair.
Bail
By moving the independent brake handle sideways, the engineer can release locomotive brake cylinder pressure that is due to an automatic brake application (a brake pipe pressure reduction). The bail has no effect on brake cylinder pressure that is due to an independent brake application.
Bakehead
Fireman (because his head was near the door of firebox when shoveling coal)
Ball (of a Rail)
The head of the rail
Balloon Track
Railroad track in the shape of a teardrop used to reverse the direction of a train.
Bend the Iron, To
To throw a switch.
Beyer-Garratt
An articulated steam locomotive with a central boiler/cab assembly pivoted between two power units. Designed for hard roads with tight curves, this type is found mostly in Africa.
Big Boy
Union Pacific 4-8-8-4 600 ton steam freight locomotive
Big C
The conductor (from the Order of Railway Conductors)
Big E
A railroad engineer (for Brotherhood of Locomotive Engineers)
Bighole
Emergency application of air brakes, usually when initiated by engineer, i.e. put her in the big hole
BIE
Brakes In Emergency; application of the emergency braking system.
Black Snake
A coal train.
BLE
Initials of Brotherhood of Locomotive Engineers union
BLF&E
Initials of Brotherhood of Locomotive Firemen and Engine-men union
Blinds
A walk way between two passenger cars covered with either canvas or leather in an accordion shape. From the outside of the blinds to the outer edge of the cars there was a space about 24 inches wide. There was a ladder running up to the top of the car in this space and the bums would grap hold of the ladder and hold on to it. That was riding the blinds.
Block
A length of track between consecutive block signals or from a block signal to the end of block system limits, governed by block signals, cab signals or both.
Block Occupancy Indicator
An indicator used to convey information regarding block occupancy.
Block Signal
A fixed signal at the entrance of a block to govern trains and engines entering and using that block.
Block System
A block or series of consecutive blocks within APB, ABS, ACS, CTC or interlocking limits.
Block Track
Track with equipment for repairing rail cars on the spot.
Blue Flag
A blue flag or signal that is placed on a car or locomotive when workers are around or under it. When a car or locomotive is blue-flagged, then it must not be coupled to or moved in any manner. The only person allowed to remove a blue flag is the person who put it there in the first place.
BMT
Brooklyn Manhattan Transit - subdivision B-1 of the New York City Transit Authority (NYCTA) subway
Bobby
British: term for a signalman in UK. Derives from railway policeman of early railways. The policeman being 'invented' by Sir Robert (Bobby) Peel.
Bogie
Australian and European term for a truck.
Boomer
Itenerent railroad workers. Always moving from one road to another.
Booster
A small two cylinder steam driven engine, manufactured by the Franklin Railway Supply Co., and attached to an axle of the trailing track of some steam locomotives to provide additional tractive effort when starting a train.
Bradley Bar
A device shaped like a hockey stick used to straighten hand holds on freight cars.
The Brains
The conductor
Brake Beam
A cross-piece in the foundation brake gear for a pair of wheels to which the leverage delivers its force to be transmitted through the attached brake head and brake shoes to the tread of the wheels.
Brake Cylinder
A cast metal cylinder with a piston that is forced outward by compressed air in applying the brakes and returned by a release spring in releasing the brakes.
Brake Pipe
Commonly called a train line, it is the pipe, hose, connections, angle cocks, cut-out cocks, fittings, etc., connecting the locomotive and all cars from one end of the train to the other for the passage of air to charge and control the brakes.
Brake Rigging
A term commonly used instead of foundation brake gear.
Brakes, Automatic
Automatic brakes are the brake controls in the locomotive that regulate the pressure of the brake pipe and apply or release the brakes for the entire train including the locomotives
Brakes, Independent
Independent brakes are the brake controls in the locomotive that apply the brakes on the locomotives only. The air hose marked ACT or BR CYL enables the lead unit to control the trailing units brakes
Branch
A portion of a division designated by a timetable. Rules and instructions pertaining to subdivisions apply on branches.
Branch Line
A secondary line of a railroad, not the main line.
Brass Hat
AA railroad executive, usually a division manager or higher, a.k.a. suits
Bridge Line Haul Road
See overhead line haul road.
Brotherhood Notch
A notch high on the reverse lever quadrant which admitted a very limited amount of steam to the cylinder making it easier on fireman, but taking longer to get over the road.
BRT
Initials of Brotherhood of Railway Trainmen union
Bull
Slang for a railroad police officer or railroad detective.
Bullhead
A condition where both drawbar knuckles are closed, making the coupling impossible without opening one knuckle (amer. slang).

C

Cab Apron
The hinged metal plate attached to the rear end cab floor of a steam locomotive, which rested on the front of the tender and formed a transition piece between the engine and tender for crew safety. Also called a deck plate.
Cab Forward
A steam locomotive with the engineers cab placed ahead of the boiler instead of behind it.
Camel back
Slang: an older rerailing device, also called a rerailing "frog". Used in pairs, one on each side to lift the wheel flanges of a derailed car and allow them to slide back onto the rail.
Carbody
Another name for the hood-type diesel locomotive. Examples: F40PH, FP45, E and F units.
Catenary
Overhead wire system on elecricfied railroads for suppling current to electric locomotives and self-propelled cars equipped with pantographs.
Centipede Tender
A high capacity tender applied to some large steam locomotives, and having seven axles, with the front two axles contained in a track casting and capable of swiveling. Major users of centipede tenders include New York Central and Union Pacific railroads (USA).
Cab Signal
A signal located in engineer's compartment or cab, indicating a condition affecting the movement of a train or engine and used in conjunction with interlocking signals and in conjunction with or in lieu of block signals.
Cabin Car or Hack
A non revenue car formally used on the rear of trains (caboose)
Caboose
End of train non revenue car
Caboose Valve
A rotary valve type of device providing means for making a controlled rate of brake pipe reduction for making a service or emergency application from the caboose.
Cantrail
From the 1889 Century Dictionary of the English Language: A timber running along the tops of the upright pieces in the sides of the body of a railway-carriage and supporting the roof and the roof sticks. Called in the United States a plate.
Car Knocker
It was common for car inspectors to tap parts with a hammer. The resulting tone of sound gave clues to the condition of those parts. Ergo, Car Knocker.
Carman
Formal name for a craft employee that inspects and repairs railway cars.
Car Toad, Car Tonk
Car inspector who checked the condition f freight and passenger cars and conducted the air brake tests
CCR
Central Control Room, a facility from which rail system operation will be monitored and controlled.
Centralized Traffic Control (CTC)
A remotely controlled block signal system under which train movements are authorized by block signals whose indicators supersede the superiority of trains.
Channel
A specified frequency for communication between train and dispatcher or 2 trains. The channel numbers (07 thru 97) are shorthand methods of designating assigned radio frequencies for transmission. For example, channel 96 means to transmit on an assigned radio frequency of 161.550 mHz.
Cinder Dick
Railroad detective (slang)
Classification Lights
Two electric lantern type lights, mounted high on front of locomotive, with lenses that could be switched from off, to white - for an extra train or to green - indicating a train running as all but the last section of a schedule. Flag holders permitted the use of white and green flags for daylite use, in like manner.
CLC
Complete Locomotive Control, retrofitted adhesion system manufactured by Woodward Governor Company.
Clear Block
A block not occupied. Sometimes used to denote a clear signal indication.
COFC
Container on flat car. Referred to in intermodal traffic.
Color Light Signal
A fixed signal in which the indications are given by the color of a light only.
Color-Position Light Signal
A fixed signal in which the indications are given by color and position of two or more lights.
Company Notch
1. Denotes reverse lever in lower quadrant using lots of steam to pull a heavy, i.e. revenue train making money for the company.
2. Also Jeffrey Van Wagenen added, "I have heard the definition you cited before, but the definition I have heard from a couple of old-timers is the opposite:  the company notch is the one with the shortest valve travel (i.e. using the least steam i.e. johnson bar closest to the center (while still making way)).  The company notch could be all the way forward to start a heavy train; near the middle while the same train was going down a slight grade.  This uses the least coal and water."
Conductor
Brakeman, with or without brains, displaying pencils.
Controlled Point
A location designated by number where signals and /or switches of a CTC system are controlled by a control operator.
Controlled Siding
A siding within CTC or interlocking limits, the authorization for use of which is governed by signal indication or control operator.
Controlled Signal
An absolute signal, the aspect of which, is controlled by a control operator.
Coon It, to
To walk across the tops of freight cars.
COT&S
Clean, Oil, Test & Stencil. Applies to air brake rework.
Covered Wagon
A nickname that is generally attached to EMD E and F units.
Cow Catcher
A metal frame on the front of a locomotive to remove obstructions from the tracks.
Creeper
A rail anchor of spring steel that is driven onto the base of the rail and bears against the tie which is prevented from moving by the resistance of the stone ballast. The name comes from the function of the anchor which is a "rail anti-creep device."
Crossing
A length of track that carries one track across another.
Crossover
A track connection between two adjacent tracks.
Crown Sheet
The iron sheet at the top of the firebox, and which was in direct contact with the heat from the firebox.It was connected to the outside shell of the boiler by "Stay Bolts" as were the "side Sheets" which comprised the sides of the firebox.
Crummy
A wooden, two truck or bobber trucked, caboose. Also called a way car, hack or, in the days of living in them, a bean shack
Cupola
A small cabin on the roof of a caboose to afford a means of lookout for the train crew.
Current of Traffic
The movement of trains on a main track, in one direction, specified by the rules.
Cut, to
Separate car(s) from a train
Cut Lever
The hand operated lever applied to all cars and locomotives, which was used to lift the coupler pin and release the knuckle in order to couple or uncouple cars and locomotives.
Cycle Braking
A rapid sequence of automatic brake applications and releases. This does not allow enough time for the reservoirs on the cars to recharge and exhausts the air pressure available to apply the brakes.
Cylinder Cocks
Drain valves, operated from engine cab, to allow condensate to drain from cylinders when locomotive had been idle for a period of time.

D

Dark Territory
A series of rail miles ungoverned by signals and unable to transmit or receive radio or cellular phone signals.
Date Nail
A small nail used by railroads from late 1800's to present used to mark the year a tie was placed in roadbed. Nails are distinctive in that each has the last two digits of placement year stamped in head. Usually found within six inches of tie end, but some are located mid tie to allow easier inspection. Rarer nails value in 100's of dollar range to collectors
Dead Head
A railroad employee traveling on a pass.
Dead Man
Usually a foot pedal that was pressed by the engineer. When pressure on the pedal was released, the train brakes were automatically applied. This was to detect sleeping or dead engineers.
Deckorate
In the days before air brakes, the duties of the brakemen included stopping the train. The brakeman would have to go to the top deck of the car - thus decorate - and wind the stem winder.
Derail
A device placed short of clearing point on a track to prevent a car or engine from fouling main track, derailing said car or engine if not removed to permit safe passage.
Diamond
A special track work item that allows two railroad tracks to cross each other at grade.
Dinger
A yard master.
Direct Traffic Control (DTC)
System of traffic control with fixed blocks, where block occupancy is granted remotely by a dispatcher. Ordinarily, only one train may occupy a DTC block at a time. Similar to TWC except that the blocks are fixed by timetable rather than granted case by case. DTC may be used in conjunction with track signalling in APB, ABS, or over dark territory.
Distant Signal
A fixed signal outside of a block system, used to govern the approach to a block signal, interlocking signal or switch point indicator. It will not convey information as to conditions affecting the use of the track between the distant signal and block signal, interlocking signal or switch point indicator to which approach is governed. It will be identified by a "D" marker.
Distributed Power Trains
Trains that have a remotely controlled locomotive embedded within the train. This allows for higher tonnage trains as the drawbar tensions are lower than an equivalent train with head-end power only.
Division
A portion of the railroad designated by timetable.
Dog
Empty boxcar train.
Dogcock
A device used in unison with a clawbar to pull spikes from the wing rails of a frog and also from the guard rail.
Dollyflopper
A brakeman or switch-tender - someone who throws switches.
Doorslammer
Slang for a passenger trainman. Usually used by freight trainmen who are adept at station switching, and all the other skills needed in general freight service. 
Double Slip Switch
Used only where space is limited, combines the functions of a crossing and turnouts to allow any one of four routings.
Double Track (DT)
Two main tracks, on one of which the current of traffic is in a specified direction, and on the other in the opposite direction.
Drag
A common expression to describe the movement of a heavy train, such as a coal drag or an ore drag.
Drawbar Horsepower
The total horsepower of a locomotive less the amount of horsepower that it takes to move the locomotive itself, the balance being available to pull the load.
Drill Track
A track connecting with the ladder track, over which locomotives and cars move back and forth in switching.
Drop
Switch a car behind the engine onto an adjacent track when the engine can't run around the car. Requires two trainmen, one to pull the pin on the car to be dropped and the other to throw the switch after the engine has passed to let the car run onto the parallel track.
Dual Control Switch
A power-operated switch, also equipped for hand operation.
Dummy
A small auxiliary signal used to control unusual movements such as a set back into a yard from a main line. Implies a complete stop and wait for a manual operation from the panel. Usually ground mounted lens: two whites for proceed and red/white for stop. Also known as dolly or dwarf.
Dump the air
Emergency application of the air brakes causing a train to stop abruptly, usually causing damage to the merchandise being carried or to the train equipment, itself
Dutchman
A short section of brake hose with a coupling(glad hand) on each end. It's used to connect two short hoses together.
Dwarf Signal
Two or three lens signal used to control a move over a switch in a yard.
Dynamic Braking
A method of train braking where the kinetic energy from the train movement generates current at the locomotive traction motors, and is dissipated in a resistor grid on the locomotive.
Dynamite
Initiation of an emergency application.
Dynamiter
A term commonly given to an brake operating valve that goes into quick-action emergency when it should not. Also called a Kicker. Dynamiting -- application of emergency (air) brakes.

E

Electric Switch Lock
An electrically controlled lock device affixed to a hand operated switch or derail to control it's use.
Electric Switch Lock
An electrically controlled lock device affixed to a hand operated switch or derail to control it's use.
Elephant Ears
Metal side plates used on some large steam locomotives to lift the smoke above the train at speed.
Emergency Application
An application resulting from an emergency rate of brake pipe reduction which causes the brakes to apply quickly and with maximum braking force for the shortest practical stopping distance.
Engine
A unit propelled by any form of energy, or a combination of such units operated from a single control, used in train or yard service.
Engine Lite
Locomotive or multiple units lite of any cars.
Engine Whistle Signals
* means a short blast of the whistle or horn

- means one long blast
* apply brakes, stop
* * answer to any signal not otherwise provided for
* * * when standing, back
* * * * call for signals
- test train brakes
- - release train brakes
- - - when running, stop at next passenger station
- - - when standing, train parted
- - - - recall flagman from south or west
- - - - - recall flagman from north or east
- * * calling attention to another train that signals are displayed for a following section
- * * * flagman protect the rear of train
* * * - flagman protect the front of train
- - * approaching meeting or waiting points
- - * - approaching crossing at grade
- * * - answer to yellow temporary reduced speed flag placed 1 1/2 miles in advance of restricted tracks
EOT
End Of Train unit (see also Caboose). An EOT transmits brake pipe pressure to the lead unit (head end locomotive), while a two way EOT is also capable of receiving a transmission from the lead unit to open the brake pipe and put the train into emergency stop (clarified by Bob Murphy).
Extra Train
A train not authorized by timetable schedule. It may be designated:
Extra -
For any extra train except work extra, the movement of which is authorized in a specified direction.
Work Extra -
For any extra train authorized by Form H train order, the movement of which may be in either direction within specified limits.

F

Facing Point Lock
A locking device which automatically locks the switch points of a spring switch in normal position.
Fairlie
Double ended Locomotive with a single central cab, Designed by Robert Francis Fairlie. Always running cab forward. Robert Francis Fairlie also designed a 'single' locomotive with one powered and one unpowered boogie and with a conventional cab at one end so can travel chimney first or bunker first.
Ferro-Equinologist
Ferro- meaning iron plus equine- meaning horse give one who studies iron horses, i.e., a railfan.
Fire Box
The "stove" where the wood, coal, oil, etc., was burned to make steam to propel the engine.
Fishplate
Length of iron, applied to either side of rail web, used to connect sections of rail together.
Fixed Signal
A signal of fixed location indicating a condition affecting the movement of a train.
Flagman
The rear brakeman. The great country music singer Jimmie Rodgers used to brag about being a flagman. Reason? Because flagmen had to know how to read so they could understand train orders.
"Flat"
A slang term use by graffiti writers for a box car without ridges on the the sides. Perfect for applying illegal graffiti by the medium of spray paint.
Flimsy
Train order, or paper paper used for train orders.
Flying Duck
A derogatory term used to describe a switchman of the former Pennsylvania Railroad, who customarily gave hand signals to their enginemen using both hands at once.
Flying Shunt
A method to roll a car into a stub track when the train is approaching from the opposite side of the switch to the stub track.

 

 
 
 
 
 

The train is stopped several yards from the switch. The engine and the car to be dropped is uncoupled from the main part of the train, and the brake reservoir on the car to be dropped is emptied. Brakeman #1 rides the car to be dropped, and brakeman #2 operates the switch.

The engine is accelerated, just prior to reaching the switch the engineer slacks the throttle, brakeman #1 pulls the uncoupling handle, then the engine speeds up, pulling away from the rolling car. Once the engine passes the switch, brakeman #2 throws the switch allowing the rolling car to go in the stub track.

Once the car is by the switch brakeman #1 applies the hand brake to stop the car. The engine now can be backed up and then used to spot the car.

Although this action was considered to be unsafe, it was occasionally done.

Flying Switch
Same procedure as flying shunt except called a different name.
Forestalling Lever
A lever next to the engineer's position on locomotives used by railroads with Intermittent Inductive Train Control. This control system would cause an automatic brake application if an engineer violated a restrictive signal, and the system required that the engineer operate the lever (ie. forestall) when passing each signal to prevent air brake automatic application which would stop the train. The IITS system included a magnetic shoe signal pickup mechanism, which was placed on the first tender axle on steam locomotives and on the lead axle on diesel locomotives, and wayside inductors in each signal block. This system was in use for many years on the New York Central railroad.
Foamers
The name used by train crews to identify the people who gather along the railroad tracks to watch or take pictures of trains.
Form D
A form used in receiving written permission to occupy track in DCS sections of railroad lines. Permission is given by Train Dispatcher or Operator.
Forty Five
Yellow signal or semaphore at 45 degrees. Train may proceed through signal, prepared to stop.
Fountain Valve
A steam supply chest mounted inside the cab at highest point on boiler, with multiple valve outlets that allowed many devices, such as the air pumps,electric dynamo,hydrostatic lubricator, etc, to be operated by steam from the boiler.
FRED
Flashing Rear End Device -- end of train telemetry device
Friction Bearing
A babbet type wheel bearing sometimes seen on old rail cars.
Frog
The intersection of two rails of a switch.
Front End
A term used to describe the smokebox end of a steam locomotive, including the exhaust stack, netting, etc.
Full Service Application
Corresponds to a handle position for the automatic brake handle. In this position the brake pipe should be at 62 PSI (down from a 90 PSI release charge pressure). When an application is made on the automatic brakes, the equalizing reservoir pressure drops in proportion to the handle movement. The self lapping valve (Automatic Brake Valve) then vents brake pipe pressure at a service rate until the equalizing reservoir and brake pipe pressures are equal. This pressure is measured on the locomotive only. It may be less further back on the train due to leakage. A minimum reduction is a 6 PSI drop to 84 PSI. After a minimum reduction is made, the automatic brake valve handle is linear down to zero. If the locomotive has a direction on the reverser handle, or the independent brakes are released, below 45 PSI BPP an emergency will occur and a valve will blow the brake pipe to zero in a hurry (corrected by Bob Murphy).
Fusee
A warning device consisting of a cardboard tube filled with a combustible mixture of chemicals that burns brightly when ignited and remains burning for varying lengths of time. Fusees are ignited and dropped on the right of way to indicate to a following train the presence of stopped or slow-moving equipment ahead.

G

Gandy Dancer
A railroad track worker. Name came from the Gandy Mfg Co. in the 19th century that made a lot of track tools.
Gateway
See Interchange Point
Gauge
Broad gauge (Spain):  1674 mm  5'5 9/10th"
Broad gauge (Portugal):  1665 mm  5'5 11/20th"
Broad gauge (Ireland):  1600 mm  5'3"
Broad gauge (Finland):  1524 mm  5' exactly
Broad gauge (former USSR):  1520 mm  5'
Standard gauge:  1435 mm  4'8 1/2"
Narrow gauge (Cape gauge):  1067 mm  3'6"
Narrow gauge (meter gauge):  1000 mm  3'3 37/100"
Gauge Cocks
Valves on the boilerhead - usually three in number - to let the crew know the depth of water over the "crown sheet" in event of a broken water glass, which gave a visible indication of water depth. and as a means to check the accuracy of the water glass indication.
Glad hand
The metal attachments to which train line air hoses connect
Goat
A yard engine.
Groundhog
A slang term for a promoted engineer with trainman seniority.
Grade Resistance
Resistance that results from the energy you must put into a train to lift it vertically. The energy is returned without loss when the train comes back down again.
Grainer
Rail slang for covered hoppers, which are often used to transport grain and other bulk, fluid solids.
Greaser
A section of curved track that has flange lubricators.
Green Eye
A slang term for a clear signal.
Grip
Trainman's suitcase.
Guinea, or Guinny
A green worker or one who is not an familiar with job requirements.

H

Hand Brake
A manually operated brake used to hold rail cars from moving.
Hand Signals
Before the advent of radios, signals were given by hand or lantern There were innumerable ways to communicate direction, destination, speed, or stop. Most railroads had their own set of distinct signals.A signal given with the hand in a vertical zipper operating motion upon the chest usually designated a mainline movement. Five fingers exposed on the hand, or a small circle with a lantern at night indicated track five,both hands with all fingers held up,or a small double circle, track ten etc. There were signals to fit almost any condition and learning to read them was sometimes an art in itself.
Haul, Short
The act of routing freight such that the haul takes maximum advantage of the originating railroad, at the disadvantage of another railroad which had to be used to carry the freight part of the way to its destination. The railroad which suffered the disadvantage was said to be "short hauled."
Head End
The front of the train. Use of this term is declining with the demise of the caboose.
Head End Power
A power system installed on diesel-electric passenger locomotives, used to generate "hotel load" power to the passenger train, including train heating and air conditioning. A head end power system may use either the locomotive's prime mover, or it may use a separate HEP engine generator set installed at the #2 end of the locomotive.
Headway
Time interval between two following trains.
Helper
Any locomotive added to assist a train up a grade.
Hi-Cube
An oversized boxcar usually used to haul autoparts.
Highball
A signal given to proceed at maximum permissible speed.
High Iron
The railroad's mainline, usually with more ballast and heavier rail, which made this track higher than yard track.
High Rail
Main track.
Hobo
An individual who rides freight trains to get from town to town. Not to be confused with a bum, a hobo is a transient worker.
Hog
A locomotive
Hoghead, Hogger
A railroad engineer
Hog Law
Refers to ICC hours of service regulations.
Holding Lights
Amber or green light signal displayed at certain station platforms at or near the conductor's position, to regulate train spacing.
Holy Roller
A graffiti slang term for a car transport car. Like for their great length, perfect for doing an end to end and other large "productions" with the illegal spray-paint techniques.
Home Signal
A special red signal that requires the train crew to call the dispatcher for orders before the train can proceed.
Hooking Up
The act of shortening the duration of the steam admission setting on a steam locomotive, using a Johnson Bar or Power reverse wheel or lever, thereby trading power for speed.
Horsepower per Trailing Ton.
The total horsepower of all working locomotives divided by the total trailing weight of the train in tons.
Horsing Lever
The lever on a steam locomotive used to manually adjust the valve setting (ie. cutoff). Also known as the Johnson bar. When engines became larger in size, a manual adjustment was no longer practical and air operated motors were used for this purpose, and a smaller lever or wheel located in the cab of the steam locomotive was used to adjust direction and cutoff.
Hostler
A person who operates engines in engine house territory and works under the direction of the engine house foreman (inside hostler). Some railroads created outside hostlers after a limited exam, who could deliver engines anywhere in the terminal.
Hostler's Controls
A simple throttle to allow independent movement of locomotives not equipped with engineers controls.
Hospital Train
A train consisting of damaged or wrecked rail cars being transported to a repair point on their wheels. Some cars have no operating brakes or intact train line. Many times a long flexable hose is used to transmit brake pipe pressure around cars with damaged train lines. Such a train must have a car on the rear with an operating brake controlled via the hose. "Hospital Trains" are also restricted to speed as well.
Hot Box
On friction bearings, an overheated journal bearing.
Hot Spot
Loaded double-stack or container train.
House Track
A track entering, or along side a freight house. Cars are spotted here for loading or unloading.
Hump
A rail yard with a hill. Cars are cut off in motion at the top of the hump and gravity pulls the cars to the classification tracks.

I

Independent Break
The brake control on a locomotive used to control the locomotives air brakes.
IND
INDependent City Subway - subdivision B-2 of the New York City Transit Authority (NYCTA) subway
Initial Station
The first station on each subdivision from which a train is authorized to occupy the main track.
Interchange Point
The point at which two or more railroads join. Traffic is passed from one road to another at interchange points.
Interlocking
An arrangement of signal appliances so interconnected that their movements must succeed each other in proper sequence. It may be operated manually or automatically.
Interlocking Limits
The tracks between the outer opposing absolute signals of an interlocking.
Interlocking Signals
The fixed signals of an interlocking, governing trains using interlocking limits.
Intermodal
Freight traffic that refers to containerization of freight for easy transloading to different modes of transportation. See TOFC,COFC, Piggyback.
Iron Bender
A switchman.
IRT
Interboro Rapid Transit - subdivision A of the New York City Transit Authority (NYCTA) subway

J

Jerkwater Town
A small town with few facilities, identified on the railroad by the existence of a water plug only.
Jew Bar
A device that holds a track in gauge. Used on sidings or industrial track.
Johnson Bar
Valve gear adjustment lever.
Join the Birdies, to
To jump from a locomotive cab before a collision.
Joint Facilities
Any facilities owned by two or more railroads.
Journal Box
Metal box around axle bearing for holding a lubricant saturated pad next to the wheel bearing.
Jumper
British: a passenger leaping from a moving train on the blind side to avoid paying.

K

Kettle
(Steam) engine (amer. slang).
Key-By
The act of lowering an automatic stop arm in order to pass a red signal.
Kicker
A common expression for an emergency brake application which occurs when a service brake application is intended or when no application is intended.
Knuckle
The movable portion of the drawbar coupler.

L

Ladder Track
A series of turnouts providing access to any of several parallel yard tracks.
Layshaft
A hand operated throttle connected to the governer on a diesel locomotive.
LCL
Less Than Carload Lots. Brakemen on local freight runs used to have to unload LCL merchandise at stations on their territories. This merchandise was usually carried in partially loaded - thus "Less than Carload lots" - boxcars, usually right ahead of the caboose.
Lead Rail
Rail between the frog and the switch.
Lightning Slinger
Slang: railroad telegrapher.
Line Haul Road
A railroad that handles freight over a medium to long distance.
Linked Up
When a 2-way EOT is in communication with the HOT allowing it to dump the train from the rear.
Live rail/Dead rail
A railroad track scale was usually unable to handle the weight of a locomotive, therefor it was necessary to provide a way for the locomotive to pass the scale without damaging it. The "live rail" was the track where the cars were weighed, the "dead rail" allowed the locomotive to pass over the scale without damage.
Locomotive
Locomotives are units propelled by any form of energy, or a combination of such units operated from a single control station, used in train or yard service
Locomotive Speed Limiter
A modern device used to control train speeds. All engines on Amtrak's NEC must be so equipped.
Low Arm
A nickname for a restricting signal in the days of the semaphore with the arm down 45 degrees.
Low Irish
Stands for medium clear signal.
Lubricating Arm
The lubricator forced valve oil into the valve chamber to lubricate the steam valve, and the lubricating arm on a mechanical lubricator drove the pump that supplied this lube.

M

Main Track
A track extending through yards and between stations which must not be occupied without authority or protection.
Mallet
Reference to the Mallet Articulated Cab Forward steam locomotives used by Southern Pacific railroad in the 30's, 40's and 50's.
Manual Block System
A series of consecutive blocks, governed by block signals operated manually, upon information by telegraph, telephone or other means of communication.
Maplines
Short lines in Connecticut and Massachussets, USA
Marker
A train signal that is used to indicate the end of the train.
Mikado
A steam freight locomotive having a 2-8-2 wheel arrangement, pioneered in a design for the emperor of Japan in 1912.
Mile Post
A post or sign on pole each mile along the track that shows the distance from a predefined location such as a major rail terminal.
Monkey Motion
Slang for the valve gear linkage on a steam locomotive.
Monkey's Tail
Slang for the handle of a switch stand, as in twisting the monkey's tail.
Motor
  1. The electrical machine (traction motor) geared to the axles of all diesel-electric and electric locomotives, and used to convert the electrical energy provided by the diesel engine and main alternator in a diesel electric locomotive, or the transformer output in an electric locomotive, to mechanical force in the form of tractive effort.
  2. The descriptive term used on the electric division of the Great Northern railroad to designate an electric locomotive.
Mother and Slug
The name used for a locomotive and slug when MU'd for yard or road operation.
MOW
Maintenance Of Way
Multiple Main Tracks
Two or more main tracks, the use of which is designated in the timetable.
MU
Multiple Unit. A lead locomotive followed by one or more locomotives. Cables between the MU connectors bring the electrical signals in party line fashion to the trailing units (clarified by Bob Murphy).
Mud Hen
A non-superheated steam engine.
Mud Ring
The lower part of the boiler of a steam locomotive directly in front of the firebox, where boiler scale and sediment settled as the engine operated. A removable plug was located at the bottom of the boiler in this area, and this plug was removed during the monthly boiler wash to flush this contamination from the boiler.
Mule
A movable, hand-carried derail that is placed on either rail.
Muzzle Loader
Term used to describe a hand fired locomotive.

N

NEC
North-Eastern Corridor -- the Amtrak route with intensive passenger traffic that connects Washington, DC, Philadelphia, New York City, and Boston
19 & 31 train orders
These types of orders were transmitted to train crews. They covered vast area of conditions such as fixing meeting points, speed restrictions.
NORAC
Northeast Operating Rules Advisory Committee: the operating rules the many USA Northeast Freight and Passenger Railroads operate under.
Number Dummies
Clerks who worked as yard checkers

O

Old Head
One who has been around long enough to become familiar with his work or who "has his head cut in" - knows how to do his job well.
OPTO
One Person Train Operation - the motorman (engineer) performs all the functions of a conductor and an engineer on a passenger train.
ORC
Old Reliable Conductors -- The union that represented conductors during the mid to late 19th century.
Originating Line Haul Road
The railroad where any freight shipment starts.
Originating Station
The first station on each subdivision from which a train is authorized to occupy the main track.
OTM
Other Track Material -- materials other than ties and rails, generally refers to spikes, tie plates and rail anchors
Overhead Line Haul Road
Any railroad or railroads between the originating line haul road and the terminating line haul road. Also known as a bridge line haul road.
Overlap
A section of track where the control length of a signal overlaps the next signal to reduce the risk of collision if the train fails in braking before the stop signal.
Overlap Sign
A sign marking the limit of control of a block signal.
Out of Station (O. S.)
Report the telegrapher would give the dispatcher on the Rock Island and presumably other railroads when the train would be past their station.

P

Paired Track
When two railroads own single track lines, they may reach an agreement whereby one railroads track services both roads in one direction, while the other railroads track services both roads in the other direction.
Panel
British for the Centralized Control Tower.
Pantograph
An electrical trolley carried on a collapsible and adjustable frame. Used on electrified locomotives and self-propelled cars for current pick-up from the catenary system.
Partial Service Application
Reducing the brake pipe pressure at a service rate but not enough to cause the reservoir and cylinder pressure to equalize.
Peg
British: a signal post.
Pig
A TOFC or COFC type car.
Piggyback
TOFC or trailer on a flat car. Originally used when truck trailers were loaded onto flat cars for shipment by rail.
Piglet
A locomotive engineer trainee.
Pilot
An employee assigned to a train when the engineer or conductor is not acquainted with the rules or portion of a railroad over which the train is to be moved.
Pin
1. A piece of metal used to lock the coupler to keep cars coupled together. Also a term meaning to push in the slack when uncoupling cars.
2. A brakeman. Third Pin -- the third brakeman required in Indiana on all trains more than 69 cars in length. Head Pin -- a brakeman that rides the head end or locomotive.
"Pins and Knuckles"
P/K, train inspection.
Plant
Slang for interlocking.
Plug
Pocket
Portion of track within a terminal on which a train may stand for a period of time
Pomptrolli
South-African: a hand-operated pump-action inspection cart.
Pony Truck
The casting and wheel set or wheel sets which make up the leading wheels of most steam locomotives, intended to guide locomotives through curves and switches, and used to properly distribute the weight of the locomotive.
Position Light Signal
A fixed signal in which the indications are given by the position of two or more lights.
Power
A name used to mention the engine units on a train.
Prime Mover
A V-type diesel with 8 to 20 cylinders rated at about 125 hp per cylinder if normally aspirated or 250 hp per cylinder if Turbo charged.
Private Car/Business Car
Coaches owned by private individuals/railroad (for use of corporate officials or supervisors). Cars were positioned at end of trains and train crew were to remain off these cars except in performance of duties. Crew was also to see that occupants of these cars were not disturbed at all costs
Pumping Signal
Any fixed signal including Absolute and Intermediate block signals, who's indications change rapidly from one indication to another and then back again due to track circuit or signal circuit failure. An engineer encountering such a signal will be governed by the most restrictive indication the signal can display.
Pusher
A helper added at the rear of a train.
Pussyfoot
Railroad detective, police, or security personnel, often found in plain clothes in rail yards or piggy-back lifts where high-dollar freight is being moved.
Puzzle Switch
Another name for a slip or double slip switch.

R

RAC
Railway Association of Canada (the AAR in Canada).
Radio Train
A heavy train that has additional "slave" locomotives located in the middle of the train that are controlled by the engineer remotely by radio.
Rail Weight
The number of pounds per yard that rail weighs. Currently rail is being rolled at 112 to 145 pounds per yard.
Rake
Wagons/carriages semi permanently joined in an articulation rather than via a coupler
Red Eye
A red signal or horizontal semaphore arm requiring the train to stop and proceed with caution.
Reefer
A common slang term for a refrigerator car.
Regenerative Braking
Braking mode of modern electric locomotives, where the motors act as generators as with the dynamic braking but, instead of being converted into heat, the current is fed back to the supply. Return energy from asynchronous motors is around 90%.
Register Station
A station at which a train register is located.
Regular Train
A train authorized by a timetable schedule.
Repeater Signal
Signal placed on the opposite side of the track from the controlling signal. It repeats the aspect of the controlling signal for a greater range of vision.
Rerailer
A heavy metal casting which was designed to be placed near a derailed wheelset of a locomotive or car, for the purpose of guiding the wheelset back onto the rail. Steam locomotives and early diesels usually carried rerailers on hooks on the tender trucks or frame (steam locomotive) or on the frame of a diesel.
Restricted Speed
A speed that will permit stopping within one half the range of vision; short of train, engine, railroad car, stop signal, derail or switch not properly lined, looking out for broken rail, not exceeding 20 MPH.
Retainer
A device added to the braking device on a car, to allow a portion of the air pressure to be retained in the brake cylinder of a car to help restrict the movement of a train on severe downgrades.
Revenue Collection Train
A train which picks up the revenue collected by the railroad clerk.
Ribbon Rail
Continuous welded rail, laid in 1/4 mile lengths then welded end to end to make a continuous length.
Rip Track
A small car repair facility, often a single track in a small yard. Name derived from "Repair, Inspect and Paint."
Rolling Resistance
Resistance that is made up of wheel friction, journal friction, and wind resistance. It is non recoverable.
Rotary Dump Car
A car that is unloaded by turning it completely over.
Rotary Dump Coupler
A specially designed coupler used in rotary dump cars that rotate allowing them to be dumped without being uncoupled.
Ruling Grade
The particular point on the run at which the combination of grade and curve resistance makes the train pull hardest and , therefore, "rules" how heavy a load can be given to the locomotive.
Run In
Describes the action of the slack between the cars moving forward and hitting against the engine. A run out would be the opposite effect.

S

Saw-by, Double Saw-by
Maneuver used by two trains at meeting point, when train on siding is too long for the siding. Double saw-by is complicated maneuver allowing two trains that are both longer than the siding at meeting point to pass one another at that siding.
SBU
Sense and Brake Unit (see also Caboose)
Scab
Non union member doing work usually contracted by railroads for railway union labor contracts.
Scrap Iron
Broken knuckle due to uncontrolled slack action in train or overly aggressive starting technique.
Schedule
That part of a timetable which prescribes class, direction, number and movement for a regular train.
Section
One of two or more trains running on the same schedule, displaying signals or for which signals are displayed.
Semaphore Signal
A signal in which the day indications are given by the position of a semaphore arm.
Shaker Bar
A tool carried in steam locomotive cabs that would be placed on the grate levers mounted in the cab deck to allow the fireman to shake the grates in the firebox, dumping ashes into the ash pan below the firebox.
Shay
A type of steam locomotive using a gear drive in place of a side rod drive, designed by Ephraim Shay in the late 1800's, and produced by what became the Lima Locomotive Works. This locomotive was designed for logging and other operations where heavy grades and sharp curves existed and prevented the use of side rod type locomotives.
Shock
The effect of a sudden change in speed of a car, locomotive or train, or part of a train.
Shoo Fly Track
A temporary track built around a train wreck or washout
Shunting Movements
Movements inside of stations and yards for making up trains, moving cars between different tracks and similar purposes. Shunting movements are done under simplified conditions with restricted speed and in viewing range.
Side Track
A track auxiliary to the main track.
Siding
A track auxiliary to the main track for meeting or passing trains. The timetable will indicate stations at which sidings are located.
Signal Aspect
The appearance of a fixed signal conveying an indication as viewed from the direction of an approaching train; or the appearance of a cab signal conveying an indication as viewed by an observer in the cab.
Signal Dolly
Train that delivers supplies to towers.
Signal Indication
The information conveyed by the signal aspect.
Signalling System
A system to ensure the safe movement of trains by means of lineside indications and/or indications given in the driver's cab.
Signalman
The man who controls the signals and authorizes the movements of trains on running lines
Single-Car Test Device
Is used to test the air brake equipment on car that is sent to a repair track
Single Track
A main track upon which trains are operated in both directions.
Skipper
The conductor
Slack
The motion, forward or back, that one or more cars, locomotives, or parts of a train has without moving other coupled cars, locomotives, or parts of the train. Loose slack is the free movement or lost motion between parts of a train. Spring slack is the movement beyond the free or lost motion brought about through compressing the draft gear springs. Slack is necessary so as to start one car at a time and so that the train may be operated around curves and over high and low places.
Slack Action
Movement of part of a coupled train at a different speed than another part of the same train.
Slippery Track
A highly greased track near the roundhouse or back shop where a newly rebuilt locomotive could be run in without going anywhere, and without calling an engine crew or pilot.
Slug
A small, ballasted, four or six axle unit, semipermanently coupled to a locomotive that does not have a prime mover, but does have traction motors. Generally used in yard duty where the switcher has enough horsepower, but not enough tractive force to push long strings of cars up a hump.
Smoking to a Meet
In steam service, pre-radio, making smoke to alert awaiting opposing train that you were approaching meeting point.
Snake
A switchman belonging to the SUNA, the Switchman's Union of North America.
Snipe
The title of a track laborer or Gandy dancer. One who builds or repairs railroad track.
Speeder
A four-wheel MOW vehicle to carry men and supplies to and from a railroad work site.
Spotter
A company employee charged with spying on other employees -- especially old time passenger conductors who collected cash fares from passengers and sometimes did not turn all the receipts in to the company at the end of the trip.
Spotting
The act of placing a car in a specific location on a track.
Split Switch
A term referring to the condition that exists at a switch when one pair of wheels under a car follows a course different from all other wheels under the car, generally resulting in a derailment.
Spring Switch
A switch equipped with a spring mechanism to restore the switch points to original position after having been trailed through.
Stack Train
Train made up entirely or mainly of single or double stack containers on flatcars designed for just that purpose.
Standing Cut
A term for making a cut of cars by walking to the cut to be made rather than pulling the cut to you
Station
A place designated in the timetable station column by name.
Stem Winder
Nickname for a staff brake which consists of a vertical rod and a wheel at the top of the rod for the leverage to wrap the brake chain around the vertical rod to stop or secure the car. A pawl was provided to hold the brake applied.
Stinger
A portable insulated pole used by railroads (and transit authorities) with third rail trackage. The pole is used to "reach" from an existing third rail power source to the pickup shoes of the electric locomotive in instances where the shoes of the locomotive are not contacting the third rail. The stinger can also be used to move electric locomotives within a shop complex.
Stub Track
A form of side track connected to a running track at one only and protected at the other end by a bumping post or other obstruction.
Subdivision
A portion of a division designated by timetable.
SUNA
Initials of Switchmen Union of North America
Sun Kink
A section of rail that elongates and bends out of alignment due to heat expansion. (see photos 1 and 2)
Superior Train
A train having precedence over another train.
Swing Man
Supplementary brakemen added to a crew for all or part of a trip, perhaps to give more hand brake capacity in mountainous territory, or for other reasons.
Switch Point Indicator
A light type indicator used in connection with facing point movement over certain switches to indicate switch points fit properly.

T

Tallow Pot
Fireman. In the 1800's tallow was used as a lubricant.
Tangent Track
Straight track.
Tare Weight
The weight of an empty car.
TCS
Traffic Control System
TCU
Transportation Communications International Union, represents clerks, car-men, yardmasters, and supervisors.
TDS
"Total Disolved Solids." A sample of boiler water was taken and tested before each steam locomtive was despatched and the total disolved solids in the water was indicated by a hydrometer at a certain temperature.If the total was too high, the boiler would "foam"and allow water into the cylinders,causing lubrication to be washed off pistons and valves.The cure for "Foaming" was to blow water out of the boiler through the "Blow off cocks" and replace with fresh water through the "injectors" until T.D.S. was reduced to a proper level.
Team Track
A track on which rail cars are placed for the use of the public in loading or unloading freight.
Telemetry
Another name for an EOT device which transmits End Of Train info to engine. Also "Telem", "Tele", "FRED", and "Freddie".
Tender
A vehicle connected to most steam locomotives which carried the coal (or oil) and water for the locomotive.
Terminating line haul road
The last railroad over which any shipment travels.
Terminating Station
The last station on each subdivision to which a train is authorized to occupy the main track.
Throbbing Red
A single flashing red light indicating Stop and Proceed or in some cases (depending on the railroad) a flashing red light indicating Restricting. No stop required, however a speed restriction applies.
Tightlock Coupler
A specially designed coupler used mostly on passenger cars that minimize slack and have interlocking features.
Timetable
The authority for the movement of regular trains subject to the rules. It may contain classified schedules and includes special instructions.
Toepath (Towpath)
Towpath originated with canal barges and referred to the path alongside the canal used by the horses that pulled the boats, hence towpath. It was later used to describe the path alongside the first railroad tracks, because before steam locomotives were developed for the purpose, the original power was furnished by horses that pulled the cars. The horses could not walk between the rails because of the ties, therefore they walked on a path alongside the rails, the towpath. In later years, some railroad workers, unfamiliar with the history of the walkway, began referring to it as a toepath. Both versions are equally acceptable now.
TOFC
Trailer on a flat car. Refers to intermodal shipments.
Tons per Operative Brake
Gross trailing tonnage of the train divided by the total number of cars having operative brakes. (not including locomotives)
Tommy Dodd
British slang for a subsidiary semaphore signal on the same post or bracket as the main signal to which it applies.
Torpedo
An explosive cap fastened to the top of the rail and exploded by the pressure of a rolling wheel to give an audible indication of conditions on the track ahead.
Track Bulletin
A notice containing information as to track conditions or other conditions, necessary for the safe operation of trains or engines.
Track Car
Equipment, not classified as an engine, which is operated on track for inspection or maintenance. It may not shunt track circuits or operate signals and will be governed by rules and special instructions for trains other than passenger trains.
Track Circuit
An electrical circuit of which the rails of the track form a part. The track circuit is the basis of signaling systems.
Track Gauge
The distance between the inner faces of the track heads. Nominally, 4' 8.5"".
Track Head
The top of the track on which the wheels roll.
Track Pan
A water filled trough placed between the rails at certain locations on a railroad's main line, each trough having a length of up to 2500 feet, for the purpose of adding water to the tender of a steam locomotive via an air activated scoop which was located on the underside of a locomotive tender. The use of a track pan arrangement prevented a need to stop to obtain water. Users of track pans included the New York Central, the Pennsylvania, and the Baltimore and Ohio Railroads in the US.
Track Permit
A form used to authorize occupancy of main track where designated by special instructions.
Track Side Warning Detector
Wayside detectors which are provided at various locations as shown in the timetable which detect such conditions as overheated journals, dragging equipment, excess dimensions, shifted loads, high water and slides.
Track Warrant Control (TWC)
A method of authorizing movements of trains or engines or protecting men or machines on a main track within specified limits in territory designated by special instructions or general order.
Track Web
The thin section of track between the base and the head.
Trackage Rights
An agreement between two railroads according to which, one railroad buys the right to run its trains on the tracks of the other, and usually pays a toll for the privilege. That toll is called a "wheelage" charge.
Traction Motor
The electric motor that transfers the electrical current generated by the locomotive to the rail.
Tractive Force
The amount of force at the driving wheel rims to start and move tonnage up various grades.
Trailing Truck
A fabricated or steel casting containing one, two, or three wheel sets, located under the engine cab and firebox of some steam locomotives.
Train
An engine or more than one engine coupled, with or without cars, displaying a marker and authorized to operate on a main track.
Train Brake
The combined brakes on locomotive and cars that provides the means of controlling the speed and stopping of the entire train.
Train Line
A cable of series of hoses used for connecting electrical or steam (in older passenger equipment).
Train of Superior Right
A train given precedence by train order.
Train of Superior Class
A train given precedence by time table.
Train of Superior Direction
A train given precedence in the direction specified in the time table as between opposing trains of the same class.
Train Order
A message changing the meeting point between two trains. For movement of trains not provided by timetable train orders will be authorized by, and over the signature of the director of train dispatching or chief dispatcher.
Train Order Signal
Fixed signal near the entrance to a river tube, bridge or at stations with moving platforms. Two lunar white mean Proceed without orders according to rules, two red mean Stop, stay and call for orders. Also: a signal at a station that indicates by its position or by its color, that train orders are to be delivered to a train, or that no orders are to be delivered.
Train Register
A book or form used at designated stations for registering time of arrival and departure of trains, and such other information as may be prescribed.
Triangle
Additional track laid at a major junction to allow trains to be turned by running the three sides of the triangle rather than reversing in a wye. Found outside major terminal stations where fixed passenger sets need to be turned to equalize flange wear.
Tri-Level
Enclosed freight car for carrying 3 levels of automobiles.
Triple Valve
An operating valve for charging the reservoir, applying the brake, and releasing the brake.
Truck Hunting
Rapid oscillation of an empty car truck at high speeds where the flanges tend to ride up on the head of the rail.
TTC
Toronto Transit Commission, public transit system operating in Toronto, Ontario, Canada. First subway in Canada (1954). Largest light rail system in North America.
Turnout Number
The ratio of the length of the tangent track to an equal unit of space between the tangent track and a point on the branch track.

U

UDE
Undesired Emergency. An emergency that is not initiated by a crew member.
Unit
Another term for a locomotive engine.
Unit Train
A train composed entirely of one commodity, usually coal or mineral, and usually composed of cars of a single owner and similar design, and usually destined for a single destination.

V

VAN
A term used in Canada for a caboose.
Variable Switch
A switch, designated by letter "V" or bowl painted yellow, when trailed through the switch points remain lined in the position to which forced.
Varnish
Term used to refer to passenger trains, dating back to the late 19th century and the varnished passenger coaches of the luxury trains such as those employed on the LV's Black Diamond and the C&O's Sportsman

W

Wandle
Affectionate rail slang for Wheeling and Lake Erie Railway which was successor to most Nickel Plate Trackage.
Water Plug
The standpipe where a steam locomotive would stop to fill its tender with water.
Wheel Knocker
Another name for car knocker. This person would check the wheels for flaws.
Wheel Pull
Caused by the friction between the brake shoe and the wheel and transmitted to the rail.
Wheel Rolling
The wheel rotating on its axle theoretically without motion existing between the wheel and the rail at the area of contact.
Wheel Slipping
The wheel rotating on its axle with motion existing between the wheel and rail at the area of contact.
Wheel Sliding
The wheel not rotating on its axle and motion existing between the wheel and rail at the area of contact.
Whistle Post
A specially marked post on the engineer's side of the train that tells him when to start whistling for a grade crossing. Slower trains may delay whistling until closer to the crossing.
Wide Vision Caboose
Caboose with center areas extended out past normal sides of caboose allowing for unobstructed forward viewing.
Windy
A slang term for a car going down a track with no air or hand brake applied
Wye
A track shaped like the letter "Y", but with a connector between the two arms of the "Y". A wye is used to reverse the direction of trains or cars. A train pulls completely through one leg of wye, the switch is thrown and reverses the direction, allowing the movement across the semi-loop track of the wye, and the train is then headed in the opposite direction.

Y

Yard
A system of tracks, other than main tracks and sidings, used for making up trains, storing of cars and for other purposes.
Yard Limits
A portion of main track designated by yard limit signs and by timetable, train order Form T or track bulletin, which trains and engines may use as prescribed by Rule 93.
Yard Engine
An engine assigned to yard service.
Yellow Eye
A slang term for a yellow signal.
BACK